> ## Documentation Index
> Fetch the complete documentation index at: https://docs.partnero.com/llms.txt
> Use this file to discover all available pages before exploring further.

# Campaigns overview

Campaigns send partners a sequence of emails over time, instead of a single email at a single moment. A campaign has a trigger that decides who enters it, an ordered list of steps that run one after another, and rules for when somebody leaves it early.

Use a campaign when the thing you want to say takes more than one email: onboarding a new partner over their first week, nudging someone who has gone quiet, or congratulating a partner on a first sale and then following up with what to do next.

Campaigns are available in affiliate programs, under **Program → Campaigns**.

> [!NOTE]
>
> Campaigns send through your program's existing email setup rather than one of their own. Configure your sender name, sender address, reply-to address and email branding under **Emails** in **Partner portal** before switching a campaign on — see [Email settings](https://docs.partnero.com/knowledge-base/program-emails/email-settings.md).

***

### Campaigns, automations and program emails

Partnero has three ways to send a partner an email. They overlap, so it is worth knowing which one you want.

| Feature | What it does | Reach for it when |
| - | - | - |
| [Program emails](https://docs.partnero.com/knowledge-base/program-emails/overview.md) | Sends one email in response to one event, as part of how the program runs | The email is a notification: a welcome, a payout receipt, a password reset |
| [Automation](https://docs.partnero.com/knowledge-base/automation/overview.md) | Runs one action — add a tag, remove a tag, send an email — when a trigger fires | You want a single reaction to a single event |
| Campaigns | Runs an ordered sequence of steps over days or weeks, and can branch partway through | The message takes several emails, spread over time |

The short version: an automation is one thing happening once. A campaign is a series of things happening on a schedule.

***

### How a campaign is put together

Every campaign has the same four parts.

**Entry trigger.** What puts a partner into the campaign. One trigger per campaign, chosen from the same list automations use. See [Entry triggers and re-entry](https://docs.partnero.com/knowledge-base/campaigns/entry-triggers-and-re-entry.md).

**Steps.** What happens, in order, once a partner is in. There are five kinds of step: wait, send email, condition, add tag and remove tag. A condition step splits the sequence into a **Yes** lane and a **No** lane, and each lane holds its own steps. See [Campaign steps explained](https://docs.partnero.com/knowledge-base/campaigns/campaign-steps-explained.md).

**Exit conditions.** Rules that take a partner out of the campaign before it finishes. They are checked before every step, so a partner who no longer belongs in the sequence stops receiving it.

**Re-entry policy.** What happens if the same partner qualifies again later: never, after a cooldown, or every time.

A campaign can hold up to 50 steps.

***

### What a partner experiences

When the trigger fires for a partner, Partnero creates an *enrollment* — a record of that partner's progress through that campaign. The enrollment moves through the steps in order.

Steps with no wait between them run straight away, one after another, rather than trickling out over several minutes. The sequence pauses only when it reaches a **Wait** step. So a campaign that sends an email, adds a tag and then waits two days will do the first two things immediately.

An enrollment ends when:

* It **completes** — the partner reached the end of the sequence
* It **leaves early** — the partner matched an exit condition, hit a condition step that had no No lane and did not match it, or the partner was deleted
* It **fails** — a step errored, or the sequence ran 50 steps in a single pass without reaching an end, which Partnero treats as a loop and stops

Deleting the campaign removes every enrollment with it.

***

### The email frequency cap

Several campaigns can target the same partner at once, and nothing stops a sequence from containing five sends in a day. To protect your sending reputation, Partnero limits how many campaign emails one partner can receive in a rolling 24 hours.

The limit is **one campaign email per partner per day**.

Capped emails are deferred, not dropped. The enrollment stays on the step and retries once the window clears, so the partner still receives the email and the rest of the sequence carries on behind it. A sequence with several sends close together will stretch out rather than lose anything.

> [!NOTE]
>
> The cap counts campaign emails only, across every campaign in the program. Program emails and automation emails are neither affected by it nor counted towards it.

> [!NOTE]
>
> The limit is a program setting with no field in the interface yet. If you need it raised or turned off for your program, contact Partnero support.

***

### Next steps

* [How to create a campaign](https://docs.partnero.com/knowledge-base/campaigns/how-to-create-a-campaign.md)
* [Campaign steps explained](https://docs.partnero.com/knowledge-base/campaigns/campaign-steps-explained.md)
* [Entry triggers and re-entry](https://docs.partnero.com/knowledge-base/campaigns/entry-triggers-and-re-entry.md)
* [Managing and editing campaigns](https://docs.partnero.com/knowledge-base/campaigns/managing-campaigns.md)


This documentation is built and hosted on [Mintlify](https://mintlify.com), a developer documentation platform.